
Big capacity split casing water pumps are double suction water pumps and are use to pump clean water or similar liquids in physical and chemical properties. It can handle heavy sand and mud water or various corrosive after changing the pump construction and materials. The temperature of the pumped liquid should not be exceeded 80℃. And the pumps are mainly suitable for water supply in factories, mines, chemical industry, petroleum, cities, hydropower stations, various conservancy projects and irrigation in farms etc.
The model of pump represents the meaning
300S-58A
300:Diameter of suction (mm)
S:Single-stage double-suction split case centrifugal pump
58:Head (m)
A:Impeller cut via the first time


Construction Description
The suction and discharge of the pump are both under the centerline of the pump shaft, they are vertical to the shaft centerline and go to horizontal direction. You need not dismount the motor and the outlet and inlet pipes for repairing.
Main parts of pump: pump casing, pump cover, impeller, shaft, double suction seal ring, shaft sleeve,bearing etc. They are made of cast iron except the shaft material being made of fine carbon steel.We can according to user's requirement to adopt the other material.
The impeller working house is composed of pump casing and pump cover. The threaded holes for installing the vacuum meter and pressure meter are separately located at the suction flange and the discharge flange. At the bottom of the suction or discharge flange there is a threaded hole for drain.
The impeller working house is composed of pump casing and pump cover. The threaded holes for installing the vacuum meter and pressure meter are separately located at the suction flange and the discharge flange. At the bottom of the suction or discharge flange there is a threaded hole for drain.
The impeller have been done static balance test. It is fixed on the shaft by the shaft sleeves and the shaft sleeve nuts, which axial position can be adjusted by the sleeve nuts. The symmetrical distribution of the impeller to balance the axial force of the impeller.
The pump shaft is supported by two single radial ball bearing. The bearing fitted on the ends of the pump casing is installed in the bearing body and is lubricated by Ca-base grease. The double suction seal ring is used to reduce the leaking water from the pressure water house which would flow back to the suction water house.
Big capacity split casing water pump is driven by the motor through the flexible coupling. It also can be driven by diesel engine if it is necessary.
The shaft seal is packing seal. The packing ring is installed between the packing in order to prevent air leaking into the pump and cooling lubrication sealing, and while the pump working, there is a little high pressure water going through into packing cavity by the groove on the horizontally split face of the pump cover,function as water seal.
The mechanical seal depend on user's requirements.

Sectional Drawing

1.Round nut
2.Bearing house B
3.Bearing ring
4.bearing gland B
5.Water deflector
6.Pump casing
7.Pump cover
8.Double suction seal ring
9.Impeller
10.Shaft sleeve
11.Packing bush
12.Packing
13.Packing ring
14.Shaft
15.Shaft sleeve nut
16.Bearing gland A
17.Bearing hold-down ring
18.Bearing
19.Bearing house A
20.Coupling
Table of standard Performance
|
Pump model |
Capacity Q (m3/h) |
Head H (m) |
Speed n (r/min) |
Power P(kw) |
Efficiency η (%) |
(NPSH) r (m) |
Impeller diameter (mm) |
Pump weight (kg) |
|
|
Shaft power |
Motor power |
||||||||
|
250S24 (10Sh-13) |
360 485 576 |
27 24 19 |
1450 |
33.1 37.2 36.7 |
45 |
80 85 81 |
3.8 |
Φ285 |
370 |
|
250S24A (10Sh-13A) |
342 414 482 |
22.2 20.3 17.4 |
1450 |
25.8 27.6 28.6 |
37 |
80 83 80 |
3.8 |
Φ280 |
370 |
|
250S14 (10Sh-19) |
360 485 576 |
16 14 11 |
1450 |
19.8 23.1 28.7 |
30 |
79 80 60 |
3.8 |
Φ270 |
340 |
|
250S14A (10Sh-19A) |
320 432 504 |
13.7 11 8.6 |
1450 |
15.5 16.6 20.3 |
22 |
77 78 58 |
3.8 |
Φ247 |
340 |
|
300S90 (12Sh-6) |
590 790 936 |
93 90 82 |
1450 |
202 243 279 |
315 |
74 79.6 75 |
4.2 |
Φ531 |
840 |
|
300S90A (12Sh-6A) |
576 756 918 |
86 78 70 |
1450 |
190 217 247 |
280 |
71 74 71 |
4.2 |
Φ500 |
840 |
|
300S90B (12Sh-6B) |
540 720 900 |
72 67 57 |
1450 |
151 180 200 |
220 |
70 73 70 |
4.2 |
Φ470 |
840 |
|
300S58 (12Sh-9) |
576 790 972 |
63 58 50 |
1450 |
131.7 148.5 165.5 |
200 |
75 84 80 |
4.8 |
Φ435 |
809 |
|
300S58A (12Sh-9A) |
529 720 893 |
53 49 42 |
1450 |
100.4 118.6 131 |
160 |
76 81 78 |
4.8 |
Φ410 |
809 |
|
300S58B (12Sh-9B) |
504 684 835 |
47.2 43 37 |
1450 |
88.7 104 111.4 |
132 |
73 77 75.5 |
4.7 |
Φ390 |
809 |
|
300S32 (12Sh-13) |
612 790 900 |
36 32 28 |
1450 |
73.1 81 84.7 |
110 |
82 85 81 |
4.8 |
Φ348 |
709 |
|
300S32A (12Sh-13A) |
551 720 810 |
31 26 24 |
1450 |
58.1 61.4 68 |
75 |
80 83 78 |
4.8 |
Φ324 |
709 |
|
300S19 (12Sh-19) |
612 790 935 |
22 19 16 |
1450 |
45.9 47.5 47.9 |
55 |
80 86 85 |
5.2 |
Φ293 |
487 |
|
300S19A (12Sh-19A) |
504 720 829 |
20 16 13 |
1450 |
38.7 39.2 39.1 |
45 |
71 80 75 |
5.2 |
Φ268 |
487 |
|
300S12 (12Sh-28) |
612 790 900 |
14.5 12 10 |
1450 |
30.2 30.4 33.1 |
37 |
80 84.8 74 |
5.5 |
Φ251 |
660 |
|
300S12A (12Sh-28A) |
522 684 792 |
11.8 10 8.7 |
1450 |
23.3 23.9 24.7 |
30 |
72 78 76 |
5.5 |
Φ251 R122 |
660 |

Hot Tags: big capacity split casing water pump, China big capacity split casing water pump manufacturers, split casing water pump for renewable energy industry, split casing water pump for geothermal power plants, split casing pump for indoor use, medium pressure split casing water pump, corrosion resistant split casing water pump, split casing water pump for brazing













