Home > News > Content

The Influence Of Pipeline Resistance On Head And Calculation Of Pipe Loss

Oct 06, 2025

As we all know, pipes are solid substances, and water is a fluid that can flow easily. If the water inside the pipe is flowing, some of the energy must be converted into heat energy and "consumed", that is, a part of the water pressure (or called head) is lost. This is a reflection of objective things and is an inevitable law of water flow movement. Usually, we call this phenomenon of energy transformation "energy loss" (or "hydraulic loss", "loss of head"). It is calculated in meters.

Pump


How significant is the impact of pipeline resistance on head?

Some users have measured that although the vertical distance from the reservoir or water tower to the water source surface is still slightly less than the pump's head, the water volume still remains small or water cannot be pumped. The common reason is that the pipeline is too long and there are many bends in the water pipe, resulting in excessive resistance loss of the water flow in the pipeline. Generally, a 90-degree bend has greater resistance than a 120-degree bend. The resistance loss of each 90-degree bend is approximately 0.5-1 meter, and the resistance of every 20 meters of pipeline can cause a loss of approximately 1 meter in head. In addition, some users also randomly change the pipe diameters of the pump's inlet and outlet pipes, which also has a certain impact on the head. So, how much does the pipeline resistance affect the head? Next, let's look at the table below.

Do you understand the reasons for the water loss caused by the flow of water in the pipe? Question 1: It is due to the obstructive effect of the rough pipe walls.


2. It is the relative movement between different layers of water flow. 3. It is the vortex formed by the local rapid change of water flow inside the pipe fittings. The hydraulic loss of the pipeline (network) consists of two parts: the loss along the pipeline and the local loss. In engineering, we must calculate and know the quantity of this loss in order to correctly select the pump and determine the required pump head.

The pipeline loss along the entire flow path is the frictional resistance that occurs throughout the entire flow process. It is related to factors such as pipe wall roughness, pipe length, pipe diameter, and flow velocity. Based on the principles of hydraulics, its relationship can be established.

The loss along the pipeline is directly proportional to the friction coefficient along the pipeline which is related to the roughness of the pipe wall. Different pipe materials have different roughness, and cast iron pipes are relatively rough, so the friction coefficient along the pipeline is larger; plastic pipes are relatively smooth, so the friction coefficient along the pipeline is smaller. It is also proportional to the length of the pipe; inversely proportional to the pipe diameter. That is to say, when the flow rate is constant, the smaller the pipe diameter and the faster the flow velocity, the greater the loss along the pipeline; it is also directly proportional to the square value of the flow velocity. Of course, the calculation is rather complicated. A simple method can be used for estimation.

Local losses in pipelines occur when water flows through fittings such as bottom valves, valves, elbows, and reducers in the pipeline. Due to the local devices, the flow pattern changes; the direction and speed of the flow also change, and vortices appear during the flow, causing the water to collide and impact each other. This kind of hydraulic loss caused by local resistance is called local loss.

The magnitude of local loss is directly proportional to the square of the water flow velocity passing through the pipe fittings, and is also related to the shape and quantity of the fittings. If the cross-sectional shape of the fittings changes significantly and there are a large number of fittings, the local loss will be greater. Once the pipeline layout scheme is determined, the pipeline loss head must be calculated using the calculation method, and then the design head of the pumping station should be determined. Only then can the pump selection be carried out. However, the calculation procedure is relatively complex. For simplicity, the calculation data can be compiled into a table for quick reference. Additionally, a rough estimation can be made: the loss head is equivalent to 30% to 50% of the actual terrain water lifting height (measured). For smaller pipe diameters and shorter pipelines, a larger value should be taken; for larger pipe diameters and longer pipelines, a smaller value should be taken.

The pipeline's total loss along the route and local losses can be calculated using existing software, such as the selection software system developed by Yi Wei, to facilitate the calculation process.

Pressure loss when a liquid flows in a straight pipe

The pressure loss when a liquid flows in a straight pipe is caused by the friction during the liquid's movement and is called the frictional pressure loss. It mainly depends on the length of the pipeline, the inner diameter, the flow velocity of the liquid, and the viscosity of the liquid, etc. The pressure loss varies with the different flow states of the liquid. In hydraulic transmission, laminar flow of the liquid in a circular pipe is the most common, so when designing a hydraulic system, it is often desired to keep the liquid flow in the pipeline in a laminar state.


Pressure loss along the flow path of fluids in pipelines. Pressure loss during laminar flow. In hydraulic transmission, the majority of the liquid's flow state is laminar flow. In this state, the pressure loss of the liquid flowing through a straight pipe can be calculated theoretically.

Laminar flow in a circular pipe (1) The velocity distribution law of the liquid on the flow cross-section. As shown in the above figure, the liquid moves in a laminar manner in a circular pipe with a diameter of d. The pipe is placed horizontally, and a small cylinder with its axis coinciding with the pipe axis is taken inside the pipe. Let its radius be r and its length be l. The forces acting on this small cylinder along the pipe axis direction are: the pressure at the left end p1, the pressure at the right end p2, and the friction force on the cylinder surface Ff. Then the force balance equation is:

From Equation (2-6), we can conclude:

In the formula: μ represents dynamic viscosity. Since the increment of velocity du has the opposite sign to the increment of radius dr, a negative sign is added in the formula. Additionally, Δp = p1 - p2. Substituting Δp and equation (2-45) into equation (2-44), we obtain:

The integral with respect to the variable is:

When r = R, u = 0. Substituting this into equation (2-47) yields:

Then

From the formula, it can be seen that the flow velocity u inside the pipe is distributed along the radius direction according to a parabolic law. The maximum flow velocity occurs on the axis, and its value is:


(2) The flow rate in the pipeline.

The volume shown in Figure (b) of the projectile is the volume of the liquid that flows through the flow cross-section per unit time, which is the flow rate. To calculate its volume, a thin circular ring with a thickness of dr at a radius of r can be taken. The flow rate of this annular area is:

For the integral calculation, we can obtain the flow rate q:

(3) Average flow velocity. Let the average flow velocity within the pipe be υ

By comparison, we can obtain the relationship between the average flow rate and the maximum flow rate:

(4) Pressure loss along the path. In the laminar flow state, the pressure loss along the path of the liquid flowing through a straight pipe can be calculated using the formula:

From the equation, it can be seen that in the laminar flow state, the pressure loss of the liquid flowing through a straight pipe is proportional to the dynamic viscosity, pipe length, and flow velocity, and inversely proportional to the square of the pipe diameter. When calculating the pressure loss in practice, to simplify the calculation, we have μ = υdρ/Re, and substitute μ = υdρ/Re, and multiply both the numerator and the denominator by 2g to obtain:

In the formula: λ represents the friction coefficient along the path. Its theoretical value is λ = 64/Re, while in practice, due to various factors, for smooth metal pipes, λ = 75/Re is taken, and for rubber pipes, λ = 80/Re is adopted. In turbulent flow, the pressure loss is caused by the laminar flow of each particle having a regular axial movement. There is no lateral movement. One of the important characteristics of turbulent flow is that the particles of the liquid no longer have regular axial movement but instead mix and pulsate with each other during the movement. This extremely irregular movement causes collisions between particles and forms vortices, resulting in much greater energy loss in turbulent flow than in laminar flow. Due to the complexity of the turbulent flow phenomenon, until now, no satisfactory results have been achieved by studying it completely using theoretical methods. Therefore, experiments are still used for research, supplemented by theoretical explanations. Thus, the pressure loss of liquid flow in the turbulent state is still calculated using the formula, and the value of λ is not only related to the Reynolds number Re but also to the roughness of the pipe wall surface.


2. Local Pressure Loss
Local pressure loss refers to the pressure loss caused by the flow of liquid passing through valve ports, bends, changes in flow cross-section, etc. When the liquid flows through these areas, due to the changes in the direction and speed of the liquid flow, vortices are formed, causing the liquid particles to collide with each other, thereby resulting in significant energy loss.


The calculation formula for the local pressure loss in the suddenly expanded section can be expressed as follows:

In the formula: is the local resistance coefficient, whose value can only be obtained through theoretical derivation when the liquid flows through a suddenly expanded cross-section; otherwise, it must be determined through experiments. is the average flow velocity of the liquid, generally referring to the flow velocity downstream of the local resistance. The total pressure loss of the pipeline system is equal to the sum of all along-the-course pressure losses and all local pressure losses, that is:

Send Inquiry